Eurotec terrace gliders

SIHGA GleitFix is a further development of the SIHGA DielenFix.The successor to the DielenFix is a one-part system, which is fastened to the underside of the floor with three screws. The clip connection between the two glass fiber reinforced plastic plates facilitates the alignment of the fastening. Compared to the DielenFix, the system saves a stainless steel drill screw per attachment. SIHGA GleitFix can be used for nearly all types of wood with a width between 90 and 150 mm.Its height has been raised from 6 to 8 mm, which ensures perfect structural protection for the substructure and guarantees an optimal aerated terrace - a key criterion for the service life of terraces.Also new is a special attachment for the initial and end boards. Now these can also be fixed invisibly: GleitFix AE SIHGA DielenFix quantity calculation:To determine the amount required, we recommend the following auxiliary formula:Total linear meters of the substructure / plank width including gapUsing the example of a terrace with a 15 meter substructure, hallway width 144 mm, 6 mm groove:15 / 0.150  = 100 pieces The use: fastened planks not visible screwed; produced, developed and patented in Austria gives elegant appearance and safety of the screw suitable for almost all types of wood reduces errors on site upon delivery of the material; thereby bringing time savings and reduced storage costs Made of SIHGAMID®, the fiberglass-reinforced plastic from the Space Exploration secured more durable than stainless steel, even when säurehältigen woods; is extremely strong, heat, frost and UV-resistant; no material fatigue Floorboards remain intact at all visible surfaces the woods are screwed from below, which gives longer shelf life and prevents putrefaction and the direct influence of weather like swelling and shrinkage of the wood from operations reduces the crack and fracture behavior of wood in these natural processes Choice of three screw lengths Possible use for all common hallway strengths 19-40 mm variable visible joint 0-15 mm, for each suitable builders Height, material thickness 8 mm for optimum aeration and ensures optimum constructive wood protection at GleitFix® GF CS A4 screws are enclosed time-saving, convenient, accurate and matching SIHGAFIX® prevents rust and rust and stainless steel A4 BohrFix® for saltwater and chlorine environment Included SIHGAFIX® stainless, hardened stainless steel BohrFix® with drill bit and installation instructions no rust, no tearing or rupture of the screws; time-saving, convenient, accurate, all accessories accompanies SIHGA® TIP: MAGBIT® facilitates assembly For optimum adaptation to the type of wood of the boards or on the weathering situation of DielenFix® is produced with different fastening screws:Type GleitFix® GF incl. BohrFix® stainless steelType GleitFix® GF CS incl. BohrFix® stainless steel A4

It is essential for the durability of terraces is that the planks (decking) are infringed neither at the top nor at the lateral edges - exactly these important conditions are met the DielenFix®. His height of 6 mm ensures perfect constructive wood protection to the substructure and ensures optimally ventilating tete terrace - an essential criterion for the life of terraces. The enclosed SIHGA Bohrfix system screws for fastening to the substructure are specially manufactured without drilling for mounting on aluminum or wood and have a length of 29 mm. SIHGA DielenFix quantity calculation:To determine the amount required, we recommend the following auxiliary formula:Total linear meters of the substructure / plank width including gap x 2Using the example of a terrace with a 15 meter substructure, hallway width 144 mm, 6 mm groove:15 / 0.150 x 2 = 200 pieces    The use: fastened planks not visible screwed; produced, developed and patented in Austria gives elegant appearance and safety of the screw suitable for almost all types of wood reduces errors on site upon delivery of the material; thereby bringing time savings and reduced storage costs Made of SIHGAMID®, the fiberglass-reinforced plastic from the Space Exploration secured more durable than stainless steel, even when säurehältigen woods; is extremely strong, heat, frost and UV-resistant; no material fatigue Floorboards remain intact at all visible surfaces the woods are screwed from below, which gives longer shelf life and prevents putrefaction and the direct influence of weather like swelling and shrinkage of the wood from operations reduces the crack and fracture behavior of wood in these natural processes Choice of three screw lengths Possible use for all common hallway strengths 19-40 mm variable visible joint 0-15 mm, for each suitable builders Height, material thickness 6 mm for optimum aeration and ensures optimum constructive wood protection at DielenFix® II DF CS A4 screws are enclosed time-saving, convenient, accurate and matching SIHGAFIX® prevents rust and rust and stainless steel A4 BohrFix® for saltwater and chlorine environment Included SIHGAFIX® stainless, hardened stainless steel BohrFix® with drill bit and installation instructions no rust, no tearing or rupture of the screws; time-saving, convenient, accurate, all accessories accompanies SIHGA® TIP: MAGBIT® facilitates assembly For optimum adaptation to the type of wood of the boards or on the weathering situation of DielenFix® is produced in different materials or equipped with different fastening screws:Type DielenFix® II DF incl. BohrFix® stainless steelType DielenFix® II DF CS incl. BohrFix® stainless steel A4Type DielenFix® DF incl. BohrFix® stainless steel

Each PU contains the UNIA1 system screws 4.2 x 17 mm or 4.2 x 22 mm, 4.2 x 28 mm, 1 STK HELPO assembly aid and assembly instructions required for assembly.Regardless of the board geometry this is implemented quickly with the DILA decking connector. The height of the connector creates an optimal distance between the surface and substructure to prevent the formation of waterlogging.Fixing: concealed systemFixing type: sliding and fixed pointSpace distance: selectableDecking board: all soft and hardwoodsBoard length: all board lengthsBoard repl.: possible Material: A2 Stainless steel / black Special feature: system screws includedDILA2 quantity calculation:We recommend the following auxiliary formula to determine the required quantity:Total running meters of the substructure / board width including joint x 2Using the example of a terrace with 15 running meters of substructure, board width 144 mm, joint 6 mm:15: 0.150 x 2 = 200 piece

Regardless of the board geometry this is implemented quickly with the DILA C decking connector. The height of the connector creates an optimal distance between the surface and substructure to prevent the formation of waterlogging. Each package contains the UNIA1 system screws 4.2 x 22 mm and 4.2 x 33 mm required for installation. 1 piece HELPO mounting aid and assembly instructions. Fixing: concealed systemFixing type: sliding and fixed pointJoint distance: selectableDecking board: For domestic and modified wood species 19 - 32 mmBoard replacement: possible when boards joints are over 6,0 mmMaterial: PA6 30 GF black plasticTension arm: Flexible designUNIA drilling capacity: ca. 3 mm thick AluminiumSpecial feature: start and end clip modification

For invisible fastening of start/end decking boards The decking bracket provides a neat finish thanks to the invisible fastening of end boards. The decking bracket is made of glass fibre-reinforced polyamide. 40 system screws are included in the scope of delivery

Aluminium system profile Decking support system HKP Terrace gliders/ Terrace gliders Mini T-Stick Tenax spacerIf decking is to be fastened indirectly/invisibly, the edge connection to buildings (e.g. houses or walls) poses a particular challenge.The Eurotec StarterClip was specially developed for these edge connections.AdvantagesIndirect, non-visible fastening solution for edge connectionsSupports structural wood protection thanks to approx. 10 mm plank spacing to the substructureWeather-resistantInstructions for useThe StarterClip may only be used for low-movement decking. Low-movement decking includes the following types of wood, treatment methods and composite materials:LarchDouglas firWood-polymer composites (WPC)Thermowoods made from softwoods & hardwoodsAcetylated woodThe use of StarterClips is not recommended for woods with high bulk density and/or high swelling and shrinkage and only moderate stability (dimensional stability). This applies in particular to Cumarú, Ipé, Massaranduba and Robinia (false acacia).When selecting wood, particular importance should also be attached to good cutting sorting (including sorting out boards with interlocking growth and so-called "flader boards") as well as good conditioning (setting the equalising moisture content) of the decking boards.If necessary, the suitability of the wood type must be determined by the manufacturer/wood supplier.The Eurotec StarterClip is suitable in combination with the following products:Aluminium system profileDecking support system HKPTerrace gliders/ Terrace gliders MiniT-StickTenax spacer

Each PU contains the UNIA1 system screws 4.2 x 17 mm or 4.2 x 22 mm, 4.2 x 28 mm, 1 STK HELPO assembly aid and assembly instructions required for assembly.Regardless of the board geometry this is implemented quickly with the DILA decking connector. The height of the connector creates an optimal distance between the surface and substructure to prevent the formation of waterlogging.Fixing: concealed systemFixing type: sliding and fixed pointSpace distance: selectableDecking board: all soft and hardwoodsBoard length: all board lengthsBoard repl.: possible Material: A2 Stainless steel / black Special feature: system screws includedDILA2 quantity calculation:We recommend the following auxiliary formula to determine the required quantity:Total running meters of the substructure / board width including joint x 2Using the example of a terrace with 15 running meters of substructure, board width 144 mm, joint 6 mm:15: 0.150 x 2 = 200 piece

Regardless of the board geometry this is implemented quickly with the DILA C decking connector. The height of the connector creates an optimal distance between the surface and substructure to prevent the formation of waterlogging. Each package contains the UNIA1 system screws 4.2 x 22 mm and 4.2 x 33 mm required for installation. 1 piece HELPO mounting aid and assembly instructions. Fixing: concealed systemFixing type: sliding and fixed pointJoint distance: selectableDecking board: For domestic and modified wood species 19 - 32 mmBoard replacement: possible when boards joints are over 6,0 mmMaterial: PA6 30 GF black plasticTension arm: Flexible designUNIA drilling capacity: ca. 3 mm thick AluminiumSpecial feature: start and end clip modification

SIHGA GleitFix is a further development of the SIHGA DielenFix.The successor to the DielenFix is a one-part system, which is fastened to the underside of the floor with three screws. The clip connection between the two glass fiber reinforced plastic plates facilitates the alignment of the fastening. Compared to the DielenFix, the system saves a stainless steel drill screw per attachment. SIHGA GleitFix can be used for nearly all types of wood with a width between 90 and 150 mm.Its height has been raised from 6 to 8 mm, which ensures perfect structural protection for the substructure and guarantees an optimal aerated terrace - a key criterion for the service life of terraces.Also new is a special attachment for the initial and end boards. Now these can also be fixed invisibly: GleitFix AE SIHGA DielenFix quantity calculation:To determine the amount required, we recommend the following auxiliary formula:Total linear meters of the substructure / plank width including gapUsing the example of a terrace with a 15 meter substructure, hallway width 144 mm, 6 mm groove:15 / 0.150  = 100 pieces The use: fastened planks not visible screwed; produced, developed and patented in Austria gives elegant appearance and safety of the screw suitable for almost all types of wood reduces errors on site upon delivery of the material; thereby bringing time savings and reduced storage costs Made of SIHGAMID®, the fiberglass-reinforced plastic from the Space Exploration secured more durable than stainless steel, even when säurehältigen woods; is extremely strong, heat, frost and UV-resistant; no material fatigue Floorboards remain intact at all visible surfaces the woods are screwed from below, which gives longer shelf life and prevents putrefaction and the direct influence of weather like swelling and shrinkage of the wood from operations reduces the crack and fracture behavior of wood in these natural processes Choice of three screw lengths Possible use for all common hallway strengths 19-40 mm variable visible joint 0-15 mm, for each suitable builders Height, material thickness 8 mm for optimum aeration and ensures optimum constructive wood protection at GleitFix® GF CS A4 screws are enclosed time-saving, convenient, accurate and matching SIHGAFIX® prevents rust and rust and stainless steel A4 BohrFix® for saltwater and chlorine environment Included SIHGAFIX® stainless, hardened stainless steel BohrFix® with drill bit and installation instructions no rust, no tearing or rupture of the screws; time-saving, convenient, accurate, all accessories accompanies SIHGA® TIP: MAGBIT® facilitates assembly For optimum adaptation to the type of wood of the boards or on the weathering situation of DielenFix® is produced with different fastening screws:Type GleitFix® GF incl. BohrFix® stainless steelType GleitFix® GF CS incl. BohrFix® stainless steel A4

It is essential for the durability of terraces is that the planks (decking) are infringed neither at the top nor at the lateral edges - exactly these important conditions are met the DielenFix®. His height of 6 mm ensures perfect constructive wood protection to the substructure and ensures optimally ventilating tete terrace - an essential criterion for the life of terraces. The enclosed SIHGA Bohrfix system screws for fastening to the substructure are specially manufactured without drilling for mounting on aluminum or wood and have a length of 29 mm. SIHGA DielenFix quantity calculation:To determine the amount required, we recommend the following auxiliary formula:Total linear meters of the substructure / plank width including gap x 2Using the example of a terrace with a 15 meter substructure, hallway width 144 mm, 6 mm groove:15 / 0.150 x 2 = 200 pieces    The use: fastened planks not visible screwed; produced, developed and patented in Austria gives elegant appearance and safety of the screw suitable for almost all types of wood reduces errors on site upon delivery of the material; thereby bringing time savings and reduced storage costs Made of SIHGAMID®, the fiberglass-reinforced plastic from the Space Exploration secured more durable than stainless steel, even when säurehältigen woods; is extremely strong, heat, frost and UV-resistant; no material fatigue Floorboards remain intact at all visible surfaces the woods are screwed from below, which gives longer shelf life and prevents putrefaction and the direct influence of weather like swelling and shrinkage of the wood from operations reduces the crack and fracture behavior of wood in these natural processes Choice of three screw lengths Possible use for all common hallway strengths 19-40 mm variable visible joint 0-15 mm, for each suitable builders Height, material thickness 6 mm for optimum aeration and ensures optimum constructive wood protection at DielenFix® II DF CS A4 screws are enclosed time-saving, convenient, accurate and matching SIHGAFIX® prevents rust and rust and stainless steel A4 BohrFix® for saltwater and chlorine environment Included SIHGAFIX® stainless, hardened stainless steel BohrFix® with drill bit and installation instructions no rust, no tearing or rupture of the screws; time-saving, convenient, accurate, all accessories accompanies SIHGA® TIP: MAGBIT® facilitates assembly For optimum adaptation to the type of wood of the boards or on the weathering situation of DielenFix® is produced in different materials or equipped with different fastening screws:Type DielenFix® II DF incl. BohrFix® stainless steelType DielenFix® II DF CS incl. BohrFix® stainless steel A4Type DielenFix® DF incl. BohrFix® stainless steel