SIHGA® L-GoFix® MS C1 stainless steel

OPTIMAL FOR FIXING OF FACADE FORMWORK (tongue and groove). No pre-drilling the F-BohrFix® example is bolted simply and extremely clean. The SIHGA®Bohrspitze penetrates very quickly that special SIHGA® head shape allows mounting close to the edge without the timber to burst and the little decorative head can be easily and cleanly sink.IMPORTANT: Due to the tannic acid timber should be mounted outdoors exclusively with products made of stainless steel!

fastens wood to wood without pre-drilling and without countersinkingreduces crack formation or splitting of the timbers, even board materials, saves work time, additional pre-drilling extends the life of the wood  also attaches coverings made out of hard and thermo-woodcreates a perfect look, with these woods additional pre-drilling is recommended  multi-stage head with small head diameterhigh constructive wood protection and refined surface as a result of the plane head  special thread angle with sharp thread edgeshigh pull-out value  SIHGA® point with special shapeguarantees fast setting of screws without splitting  SIHGA® ribs on shaft and slip coatinglight, fast rotation and optimum fit in the wood are guaranteed  made from hardened stainless steelrust-free fastening, extremely break-proof  also available with black (SC 9 coating) and antique look (SC 11 coating)optimum on dark materials, or can be used for larch, Douglas fir and Bangkirai  including SIHGAFIX® stainless steel, Systemstift® and installation instructionstime-saving, practical, precise, all accessories enclosed; SIHGAFIX® stainless steel prevents rust from external sources and also screws into deep grooves  When using coatings such as oils, glazes and pre-greying, it is essential to consult the coating manufacturer. As a rule, the manufacturer specifies the minimum material quality of the binding agent. If the manufacturer is not known, we recommend material quality A4 (L-BohrFix® MB A4). L-GoFix® MS A2 made from A2 stainless steelstands out thanks to its good corrosion resistance and is best used in moderate, corrosive environments Because of the material properties it is strongly advised to generally pre-drill the add-on part (screw diameter + 0.5 -1 mm). The substructure, due to the different bulk densities and moisture, also in conifers, should in most cases be pre-drilled over the entire thread length with Ø 3 mm. If in doubt, we recommend carrying out pretrials

Stainless steel MOUNTS EXTERIOR WOOD PROFESSIONAL AND PERMANENTLY In mounting pack or object pack incl. assembly instructions, pencil S1 and SIHGAFIX stainless steel.The protected L-GoFix® MS multistage head combines high pullout force with a very small head diameter.The plane head conclusion gives the area a clean, elegant appearance, thereby increasing the constructive wood protection. For softer woods such as Larch, Douglas fir, pine, is the L-GoFix® MS to blow up without pre-drilling, with no pre-sinking and without the wood, simple and clean screwed from above! For harder woods such as Tropical woods or thermo-modified wood should be pre-drilled with the TerrassenFix® countersink TFB / ES II.The special SIHGA® tip guarantees very quickly attached. The integrated milling splines on the shaft and the sliding coating ensure easy screwing. Sharp thread flanks provide optimum seating in wood. These features enable universal use, even in OSB the L-GoFix® MS optimal screw to. SIHGA® Tip: For optimum constructive wood protection and to reduce the shear on screws (by the swelling / shrinking behavior of the timbers), we recommend the use of TerrassenFix® II TF or KompeFix® II KF.

SIHGA GoFix MS II is ideal for outdoor use, in the case of pergolas or carports, which are not exposed to direct weathering. The SC 7 coating has a 10 times higher corrosion protection than conventional zinc plating.Your benefit:     Fixed wood on wood up to 500 mm, even OSB boards     Without pre-drilling and without pre-drilling is screwed     A special multi-stage head reduces the gap effect in the wood     Saves 50% of storage, combined with countersunk head and disk head     Transmits high forces, is nevertheless retractable and allows close-fitting screwing     Attaches pressure-resistant insulation materials for ridge insulation     Significantly increased corrosion protection, can be painted over     For applications in the corrosivity category C4-lang or C5-mittel     Special milling ribs on the shaft and sliding coating     Pre-drilling effect, easy insertion, low-noise SIHGA® screw tip     Quick assembly, easy-to-use and time-saving     Including SIHGAFIX®, Systemstift® and assembly instructions     Time-saving, practical, precise, complete accessories are packed; SIHGAFIX® also screws in deep grooves     SIHGA® MSZ wheel for diameter 8 mm     This ornamental disc MSZ increases the pulling force of the head further to 9 kN; Visually very nice and high traction     Positive appraisal for processing with impact wrenches     Saves time and provides security, even when working overhead     ETA European technical approval with external monitoring     Reliable, externally monitored values ​​provide safety during processing and exclude quality fluctuations

The new Sihga® TeFix® screw can be screwed on cleanly on patios and facades without pre-drilling and countersinking.BENEFITS> fastens wood to wood without pre-drilling and countersinking> prevents cracking or splitting of the woods in almost all hardwoods and thermo-woods> Made from hardened, rustproof stainless steel> fastens rustproof and is extremely unbreakable> SIHGA® friction shaft with a special shape> pre-drill the board with 5 mm; the wood can swell and shrink> SIHGA® multi-stage head further developed> thanks to the extra thin head and sawtooth ribs, no displacement or chipping of the wood> in combination with KompeFix® II KF the perfect solution> increases the lifespan of the wood and the screw> including TEBIT® rustproof with holding function, Systemstift® and assembly instructionstime-saving, practical, precise, all accessories are included; TEBIT® rust-free holds the screw without a magnet and prevents extraneous rust

Developed for solid grip and precise positioning. Installation process with minimum effort and maximum resistance. Elegant appearance, integrated pre-drilling point, rapid penetration, flush head finish and versatile for outdoor purposes. Length: 25 - 120 mmDiameter: 3,2 - 6 mmHead: 3-Step-Head 

The stainless mounting of all woods, also hard and thermo wood to aluminum. The geometry is fixed without pre-drilling.Your benefit attached All specie on aluminum for attachment to aluminum profiles of up to 4.5 mm wall thickness extra long drill bit fixed without pre-drilling made of hardened stainless steel mounted stainless, even with acid group containing woods and is extremely resistant to breakage small head diameter of 8 mm elegant appearance, chipless screw Included SIHGAFIX® stainless, Systemstift® and assembly instructions time-saving, practical, precise all accessories accompanies SIHGAFIX® rust-preventing rust and screwed in deep grooves Product safety in the future SIHGA® TIPPTo prolong the life of wooden structures we recommend the use of KompeFix® and compliance with the design recommendations.

The ELITA stainless steel screws are specifically designed to securely mount wood or wood-likeTerrace and facade boards in demanding exterior applications where visual quality is paramount.The geometry of the countersunk screw head has 3 steps which permit a perfect precise flush finish. ELITA can be additionally combined with PROFILA and SOLIDA screws due to the identical diameter of the screw heads allowing a uniform screw head arrangement.Length: 50 - 80 mmDiameter: 4.5 mm, 5.0 mmHead: 3-Step-HeadBit: TXMaterial: Hardened stainless steel

OPTIMAL FOR FIXING OF FACADE FORMWORK (tongue and groove). No pre-drilling the F-BohrFix® example is bolted simply and extremely clean. The SIHGA®Bohrspitze penetrates very quickly that special SIHGA® head shape allows mounting close to the edge without the timber to burst and the little decorative head can be easily and cleanly sink.IMPORTANT: Due to the tannic acid timber should be mounted outdoors exclusively with products made of stainless steel!

fastens wood to wood without pre-drilling and without countersinkingreduces crack formation or splitting of the timbers, even board materials, saves work time, additional pre-drilling extends the life of the wood  also attaches coverings made out of hard and thermo-woodcreates a perfect look, with these woods additional pre-drilling is recommended  multi-stage head with small head diameterhigh constructive wood protection and refined surface as a result of the plane head  special thread angle with sharp thread edgeshigh pull-out value  SIHGA® point with special shapeguarantees fast setting of screws without splitting  SIHGA® ribs on shaft and slip coatinglight, fast rotation and optimum fit in the wood are guaranteed  made from hardened stainless steelrust-free fastening, extremely break-proof  also available with black (SC 9 coating) and antique look (SC 11 coating)optimum on dark materials, or can be used for larch, Douglas fir and Bangkirai  including SIHGAFIX® stainless steel, Systemstift® and installation instructionstime-saving, practical, precise, all accessories enclosed; SIHGAFIX® stainless steel prevents rust from external sources and also screws into deep grooves  When using coatings such as oils, glazes and pre-greying, it is essential to consult the coating manufacturer. As a rule, the manufacturer specifies the minimum material quality of the binding agent. If the manufacturer is not known, we recommend material quality A4 (L-BohrFix® MB A4). L-GoFix® MS A2 made from A2 stainless steelstands out thanks to its good corrosion resistance and is best used in moderate, corrosive environments Because of the material properties it is strongly advised to generally pre-drill the add-on part (screw diameter + 0.5 -1 mm). The substructure, due to the different bulk densities and moisture, also in conifers, should in most cases be pre-drilled over the entire thread length with Ø 3 mm. If in doubt, we recommend carrying out pretrials

Stainless steel MOUNTS EXTERIOR WOOD PROFESSIONAL AND PERMANENTLY In mounting pack or object pack incl. assembly instructions, pencil S1 and SIHGAFIX stainless steel.The protected L-GoFix® MS multistage head combines high pullout force with a very small head diameter.The plane head conclusion gives the area a clean, elegant appearance, thereby increasing the constructive wood protection. For softer woods such as Larch, Douglas fir, pine, is the L-GoFix® MS to blow up without pre-drilling, with no pre-sinking and without the wood, simple and clean screwed from above! For harder woods such as Tropical woods or thermo-modified wood should be pre-drilled with the TerrassenFix® countersink TFB / ES II.The special SIHGA® tip guarantees very quickly attached. The integrated milling splines on the shaft and the sliding coating ensure easy screwing. Sharp thread flanks provide optimum seating in wood. These features enable universal use, even in OSB the L-GoFix® MS optimal screw to. SIHGA® Tip: For optimum constructive wood protection and to reduce the shear on screws (by the swelling / shrinking behavior of the timbers), we recommend the use of TerrassenFix® II TF or KompeFix® II KF.

SIHGA GoFix MS II is ideal for outdoor use, in the case of pergolas or carports, which are not exposed to direct weathering. The SC 7 coating has a 10 times higher corrosion protection than conventional zinc plating.Your benefit:     Fixed wood on wood up to 500 mm, even OSB boards     Without pre-drilling and without pre-drilling is screwed     A special multi-stage head reduces the gap effect in the wood     Saves 50% of storage, combined with countersunk head and disk head     Transmits high forces, is nevertheless retractable and allows close-fitting screwing     Attaches pressure-resistant insulation materials for ridge insulation     Significantly increased corrosion protection, can be painted over     For applications in the corrosivity category C4-lang or C5-mittel     Special milling ribs on the shaft and sliding coating     Pre-drilling effect, easy insertion, low-noise SIHGA® screw tip     Quick assembly, easy-to-use and time-saving     Including SIHGAFIX®, Systemstift® and assembly instructions     Time-saving, practical, precise, complete accessories are packed; SIHGAFIX® also screws in deep grooves     SIHGA® MSZ wheel for diameter 8 mm     This ornamental disc MSZ increases the pulling force of the head further to 9 kN; Visually very nice and high traction     Positive appraisal for processing with impact wrenches     Saves time and provides security, even when working overhead     ETA European technical approval with external monitoring     Reliable, externally monitored values ​​provide safety during processing and exclude quality fluctuations

The new Sihga® TeFix® screw can be screwed on cleanly on patios and facades without pre-drilling and countersinking.BENEFITS> fastens wood to wood without pre-drilling and countersinking> prevents cracking or splitting of the woods in almost all hardwoods and thermo-woods> Made from hardened, rustproof stainless steel> fastens rustproof and is extremely unbreakable> SIHGA® friction shaft with a special shape> pre-drill the board with 5 mm; the wood can swell and shrink> SIHGA® multi-stage head further developed> thanks to the extra thin head and sawtooth ribs, no displacement or chipping of the wood> in combination with KompeFix® II KF the perfect solution> increases the lifespan of the wood and the screw> including TEBIT® rustproof with holding function, Systemstift® and assembly instructionstime-saving, practical, precise, all accessories are included; TEBIT® rust-free holds the screw without a magnet and prevents extraneous rust